Vanquish Products Currie Portal F9 Front / Rear Axle Clear Anodized SCX10-II

  

AIRCRAFT / VEHICLE / BOAT KITS. Grease / Lube / Oil.

RADIO / RECEIVER / SERVOS. WHEELS / TIRES / RIMS. Wheels / Rims / Tires / Sets.

Bodies / Lights / Accessories. Electric Motors / Speed Controls. Accessories Glow Plugs, Temp Guns, etc.. Nitro Engine Parts Tune Pipes, gaskets, etc.. Adhesives / Fluids / Tools.

Buildings / Bridges / Tunnels. Grasses / Trees / Scenery. Trains / Tracks / Sets. Accessories / Tape / Brushes. Paint - Aerosol / Spray Cans.

Paint - Airbrush / Bottles. Vanquish Products Currie Portal F9 Front / Rear Axle Clear Anodized : SCX10-II.

Brand New In Factory Packaging. PRODUCT DESCRIPTION Currie F9 Portal Front Axle for SCX10-II based vehicles The F9 Portal axles create extreme amounts of ground clearance under the center of your axle, increasing the clearance by 1/2+ (13mm). This provides the equivalent of a tire over 1 inch taller than what is on your vehicle.

The advantage of the Vanquish Currie F9 Portals is the gear reduction inside the portal (1.67:1) which can be adjusted with optional gear sets (1.4:1 Overdrive). By adding reduction at the portal, less torque is transferred through the other upstream components in the drivetrain.

These axles are a direct replacement to any Axial AR44 axle, using all stock links. These axles come with all parts needed to assemble a full front axle. Features Portal box built into the included knuckle with bolt on high steer arm for double shear mounting Gear reduction in the portal of 1.67:1 (18/30), Optional Overdrive Ratio of 1.4:1 (20/28) recommended for use in front axle only. Included Vanquish AR44 machined gear set Overall axle reduction of 6.26:1 with stock portal ratio 13mm increase in ground clearance Specifically design offset C-hubs is machined into the housing for strength, durability, clearance and scale appearance Hex to hex width of 7.66 inches, only roughly 5mm wider than a stock AR44 axle with a narrow hex Replaceable Chromoly threaded inserts used at knuckle and C-hub to ensure a stripped thread doesn't ruin your investment Brass knuckle bushing from the AR60 axles are used in place of SCX10-II sized for more durability.

Chromoly AR60 size VVD axle shafts come preassembled Chromoly stub shafts with 6mm design at the drive pin which tapers down to a 5mm thread for ultimate strength Chromoly spool Aluminum 12mm hex with set screw Compatible with stock SCX10-II Chassis mounted servo or F9 Servo on axle mount Uses all SCX10-II linkage Adjustable steering stop integrated into knuckle Complete Fast Eddy Bearings kit Licensed by Currie Enterprises Comes with One Piece Bearing Retainers (Patent Pending) Double shear shock mounts Integrated Panhard mount Upper link mounts built into third member Increased upper link clearance for more suspension up travel ability Requires the use of a 350 SLW hub or greater on Vanquish 1.9 wheels, Incision wheels will require a #4 or greater. Other wheel manufacturers offsets will vary.

Axles must be used in pairs, you cannot run a front portal axle without a rear and vice versa. Currie F9 Portal Rear Axle for SCX10-II based vehicles The F9 Portal axles create extreme amounts of ground clearance under the center of your axle, increasing the clearance by 1/2+ (13mm).

These axles come with all parts needed to assemble a full rear axle. Features Portal box integrated into the rear housing for the most clearance at the axle ends possible and a more scale appearance Gear reduction in the portal of 1.67:1 (18/30), Optional Overdrive Ratio of 1.4:1 (20/28) Included Vanquish AR44 machined gear set Overall axle reduction of 6.26:1 with stock portal ratio 13mm increase in ground clearance Hex to hex width of 7.66 inches, only roughly 5mm wider than a stock AR44 axle with a narrow hex Chromoly inner rear axle shafts are triple bearing supported Chromoly stub shafts with 6mm design at the drive pin which tapers down to a 5mm thread for ultimate strength Chromoly spool Aluminum 12mm hex with set screw Uses all SCX10-II linkage Complete Fast Eddy Bearings kit Licensed by Currie Enterprises Comes with One Piece Bearing Retainers (Patent Pending) Double shear shock mounts Upper link mounts built into third member Increased upper link clearance for more suspension up travel ability Requires the use of a 350 SLW hub or greater on Vanquish 1.9 wheels, Incision wheels will require a #4 or greater. Overdrive gear sets are recommended for use in the front axle only.

We are an authorized dealer of every product we offer in our store. There are always ways to work things out to meet your satisfaction.

Top 10 Reasons to Shop At GoNitroHobbies. We are authorized dealers of all the items we sell and all products are brand new in factory packaging. We have been serving R/C hobby enthusiasts worldwide for over 9 years. We aim to offer all of our customers with the best service to ensure their satisfaction is met.

With thousands of satisfied customers around the world, check out our feedback and you'll see why customers prefer to shop with us. We offer a wide selection of products and carry a ton of brands to ensure our customers find what they're looking for. We insure that all orders are packed properly and delivered to your doorstop safely.